For SuperLite 17 (shown) & SuperLite 27 Helmets and KMB-18
& KMB-28 Band Masks "B" side block only
The Hot Water Shroud,
Part #525-100 , can be used whenever diving
operations are conducted on mixed gas, or when diving in cold water. The
shroud helps warm the divers incoming air, thereby lessening diver heat
loss.
This Welding Lens Assembly, PART #
525-403, will fit the SuperLite 17 & 17C, SuperLite 27, the KMB-18,
and the KMB-28. The port retainers are supplied with two plug screws which
are designed to protect the two threaded holes on the port retainer which
are provided for the welding lens assembly.
There are three densities of
lens available:
PART # 525-405___lens,
Light (#5)
PART # 525-406___lens,
Medium (#10)
PART # 525-407___lens,
Dark (#12)
This assembly is designed to provide visiual
protection only!
Exploded
view & parts list
Caution
- Warning
Extreme caution MUST be exercised by all divers, regardless of helmet or
mask used, to avoid the possibility of underwater explosions when
cutting or welding. It cannot be over stressed that any underwater
explosion can result in the injury or death of the diver!
To protect your SuperLiteHelmet or Band Mask, the DSI
helmet/mask carrying bag, Part # 500-901 should
be used when transporting or storing your helmet between jobs. The DSI bag
is made from extra heavy duty, black, ripstop nylon. The bottom of the bag
is padded for additional protection. Grommeted drain holes allow the bag to
breath. The bag is also equipped with large carrying straps and side
pockets.
The Oral Nasal masks used in our helmets and
full face masks help lower the carbon dioxide levels while improving speech
communications. Our Silicone Oral Nasal Mask is made of a superior silicone
material which is hypo-allergenic and has a longer work life than standard
latex. The new silicone oral nasal, 510-690, replaces the older 510-540 &
510-547 Latex Oral Nasals.
Part # 510-690
Silicone Standard Oral Nasal for SL-27, SL-17, SL-17C, KMB-18, & KMB-28
Part # 510-569
Latex Small Oral Nasal for SL-27
Part # 510-669
Latex Small Oral Nasal for SL-17, SL-17C,
KMB-18, & KMB-28
The Tool Kit, Part
#525-620, is available for setting up and adjusting the regulator on
your SuperLite-17, SuperLite-27 helmet KMB-18 & KMB-28 Band Mask for maximum
performance.
This kit, Part # 525-130, is
designed to allow the alteration of the trim, or balance of the SuperLite
17/MK 21 diving helmet. It adds 2 lbs. to the overall weight of the helmet.
The weight replaces the exhaust body cover with no obstruction of the
exhaust port. The weight is designed to blend in to the contours of the
helmet with nothing that would hang up or become snagged while working.
THIS WEIGHT IS NOT FOR USE WITH THE DOUBLE EXHAUST!
The chin weight of the SL-27 has been removed and a side
weight added. This brings improved balance to the helmet as well as
providing an accessory ( lights, cameras, etc.) mounting area. There are
four 10-24 threaded holes with screws on the weight for this purpose. As of
8/15/95, these parts are "standard" on all SuperLite-27 helmets.
For
retrofitting older helmets, order
Weight Kit # 525-220.
This catch allows the diver a quicker, easier removal of
the helmet. As of January of 1996, this part is standard on all SL-17K,
SL-27 and SL-17C helmets.
For Retro fit upgrades order
Part # 525-106 ___for
the SL-27
Part # 525-135 ___
for the SL17C
This catch, Part # 505-010,
standard on all SL-17 Helmets, allows the yoke to be dropped without
breaking the seal of the neck clamp. The hole pattern in the Pull Pin Latch
Catch Body is identical to the Push Pin Latch Catch Body and mounts on the
yoke the same. However the screws provided with the Pull Pin Latch Catch are
longer than the original mount screws. The Push Pin Latch Catch screws
should not be used to mount the Pull Pin Latch Catch Body.
The earlier
style Push Pin Latch Catch DSI # 505-015 is now obsolete
This adapter, Part # 555-210, attaches to
the L.P. accessories port on the "B" side block. In the event of an
accidental hose break this adapter serves to restrict the flow of gas able
to escape from the port. It should always be used if the hose does not have
built in restriction.